What is your one-rep max if you lift 225 for 5?

Lifting 225 lb for 5 good reps points to a one-rep max of about 260 lb. The three common formulas put it between 253 and 264 lb: Epley gives 262.5 lb, Brzycki 253.1 lb and Lombardi 264.3 lb. It is an estimate from a formula, so treat it as a range.

Last reviewed: . These figures are estimates for healthy adults aged 18 and over. They are not medical advice, and they are not meant for pregnancy, medical conditions or anyone with a history of disordered eating. Medical disclaimer

How the three formulas treat 225 for 5

Each formula turns a weight and a rep count into the load you could lift once. They were fitted to different groups of lifters, so they disagree a little. For this set the gap between the lowest and highest answer is 11 lb.

225 lb for 5 reps by formula
FormulaEstimated one-rep max
Epley262.5 lb
Brzycki253.1 lb
Lombardi264.3 lb
Average of the three260 lb

On the bench press, this is the classic milestone set: two plates a side for five.

What if you got more or fewer reps?

One extra rep at the same weight changes the estimate more than most people expect. 225 lb for 6 reps works out to about 267 lb, and adding ten pounds to the bar for the same 5 reps works out to about 272 lb.

Estimated one-rep max if you lift 225 lb for other rep counts
Reps at 225 lbEpleyBrzyckiLombardiAverage
1225 lb225 lb225 lb225 lb
2240 lb231 lb241 lb238 lb
3248 lb238 lb251 lb246 lb
4255 lb245 lb258 lb253 lb
5263 lb253 lb264 lb260 lb
6270 lb261 lb269 lb267 lb
8285 lb279 lb277 lb280 lb
10300 lb300 lb283 lb294 lb
12315 lb324 lb288 lb309 lb

The formulas agree most closely in the middle of the table and drift apart at the high-rep end, which is why sets of more than ten reps give shakier estimates.

Training weights from this max

Programs usually set the load for a session as a percentage of your max. From 260 lb, ninety percent is 234 lb and eighty percent is 208 lb. Round down to the nearest plates you can load.

Training weights from a 260 lb one-rep max
Percent of maxWeight
95%247 lb
90%234 lb
85%221 lb
80%208 lb
75%195 lb
70%182 lb
65%169 lb
60%156 lb
50%130 lb

How far to trust it

A formula cannot see your form, how hard the set really was, or which lift you did. A grinding last rep and a set stopped with two reps in the tank give the same input and very different true maxes. Research that compared prediction equations for the bench press, squat and deadlift found their accuracy differed between lifts.

An estimated max is a planning number. It is not an instruction to load it and try. If you test a true single, warm up fully and use a spotter or safety bars.

Use your own numbers

The one-rep max calculator opens with this page's example filled in. Change any field and the result updates. Nothing you type is sent anywhere.

Frequently asked questions

What is my one-rep max if I can lift 225 for 5 reps?

About 260 lb. Epley gives 262.5 lb, Brzycki 253.1 lb and Lombardi 264.3 lb, so the honest answer is a range of 253 to 264 lb.

Which formula should I use for 225 for 5?

Epley and Brzycki are the most widely used and sit 11 lb apart or less for this set. Using the average of several formulas avoids leaning on any single one.

What should I lift for a set at ninety percent?

Ninety percent of a 260 lb max is 234 lb. Round down to a weight you can actually load.

Does this work for squat, bench and deadlift?

The formulas are used for all three, but studies have found their accuracy differs between lifts. Estimate each lift from its own set.

Is it safe to try the estimated max?

Treat it as a planning number. A true max attempt carries more risk than normal training and needs a full warm-up and a spotter or safety bars.

Sources

  1. Epley B. Poundage chart. In: Boyd Epley Workout. Lincoln, NE: Body Enterprises; 1985.
  2. Brzycki M. Strength testing: predicting a one-rep max from reps-to-fatigue. J Phys Educ Recreat Dance. 1993;64(1):88-90.
  3. Lombardi VP. Beginning Weight Training: The Safe and Effective Way. Dubuque, IA: Wm. C. Brown; 1989.
  4. LeSuer DA, McCormick JH, Mayhew JL, Wasserstein RL, Arnold MD. The accuracy of prediction equations for estimating 1-RM performance in the bench press, squat, and deadlift. J Strength Cond Res. 1997;11(4):211-213.